Stone Grey PLA Prime
Stone Gray PLA Prime.
Før musen over billedet for at zoome ind Klik på billedet for at zoome
Stone Grey PLA PrimeStone Gray PLA Prime.

Stone Grey PLA Prime

HEX #cfd5d3TD 0.6

Stone Grey PLA Prime

Polymælkesyre er en biologisk nedbrydelig, miljøvenlig plast, kendt for sin brugervenlighed og lave forvridningskvalitet. PLA Prime er vores højtydende PLA 3D print filament. Den er lavet af Natureworks Ingeo 3D850 og viser forbedret varmebestandighed, mere sejhed, god vedhæftning og mindre vridning eller krølning end traditionel PLA. PLA var altid den primære filament og anbefales stadig, når du starter din rejse med 3D-print, uden at skulle ændre nogen af ​​dine profiler kan du forbedre dit spil ved at printe med Coex 3D PLA Prime - tilgængelig i de fleste af vores standard PLA farver. Dette højtydende materiale vil være perfekt til det specielle print eller prototype, som du har ønsket at lave, men ikke var sikker på, om PLA var det bedste materiale til opgaven. Vær dog opmærksom på, at alle kvaliteter af PLA stadig vil have begrænsninger. Hvis du virkelig har brug for høj styrke og høj varmebestandighed, vil du måske udforske andre materialer til dit projekt eller din del.

Anbefalede udskriftsindstillinger

Coex 3D anbefaler følgende printindstillinger, når du udskriver med vores PLA Prime. Indstillingerne vil variere afhængigt af din specifikke udskrivningsopsætning.

  • Hotend Temperatur: 215 °C - 235 °C
    • Vigtig! Dette temperaturområde kan virke varmere, end du er vant til for andre PLA-filamenter. Brug af 100 % jomfruharpiks får vores PLA til at kræve lidt højere udskrivningstemperaturer.
  • Opvarmet seng Temperatur: 40 °C - 60 °C
    • Bemærk: En opvarmet seng er ikke et strengt krav ved udskrivning af PLA, men det anbefales at bruge en.
  • Anbefalede byggeflader/klæbemidler
    • Glasbyggeoverflade
    • PEI Build Surface
    • Magigoo
    • Malerbånd
    • Limstift
  • Køleventilator: Anbefalet. Op til 100 % blæserhastighed anbefales ved udskrivning af PLA.
  • Tørring: PLA Prime filament er hygroskopisk og vil absorbere fugt fra luften, hvis det ikke opbevares i et tørt miljø. Hvis dette sker, kan du opleve underekstrudering/inkonsekvent ekstrudering eller overdreven stringing. Du kan også høre en "popping" lyd, der kommer fra hotend under udskrivning. Vi anbefaler at tørre vores PLA ved 55 °C i mindst 3 timer, hvis den har været udsat for overdreven fugt.

Teknisk udskriftsvejledning - COEX PLA Prime

1. Materialenoter

  • Hold filamentet tørt - opbevar det korrekt og tør det før brug
  • PLA er mindre hygroskopisk end andre materialer, men korrekt opbevaring hjælper med at bevare kvaliteten
  • Tør om nødvendigt ved 55°C i 3 timer eller mere
  • Kontrollér for synlige skader før brug

2. Temperaturindstillinger

Pladetemperatur: 60°C

  • Vask pladen ofte for god vedhæftning - Brug opvaskemiddel og skyl grundigt for at fjerne olier
  • Brug produkter til pladevedhæftning om nødvendigt (limstift, WELD3D)
  • Brug brim (kant) til høje eller store udskrifter
  • Hold den omgivende temperatur stabil

Ekstrudertemperatur: 215-235°C

3. Grundlæggende parametre

PLA (Polylactic Acid) er en biologisk nedbrydelig polymer kendt for sin brugervenlighed ved udskrivning, gode overfladekvalitet og dimensionelle nøjagtighed. Perfekt til dekorative dele, prototyper og generelle udskrivningsbehov, hvor mekaniske egenskaber ikke er kritiske.

Dy se Lagtykkelse Linjebredde Volumetrisk hastighed Temperatur
0.4mm 0.2mm 0.42mm 12.0 mm³/s 220°C
0.6mm 0.3mm 0.62mm 27.0 mm³/s 225°C
0.8mm 0.4mm 0.82mm 48.0 mm³/s 230°C
1.0mm 0.5mm 1.02mm 75.0 mm³/s 235°C


4. Hastighedsindstillinger

0.4mm dyse (Volumetrisk hastighed: 12.0 mm³/s)

 Linjetype Procentdel Hastighed
Ekstern perimeter 50% 71.43 mm/s
Intern perimeter 75% 107.14 mm/s
Infill 100% 142.86 mm/s
Top/Bund 60% 85.71 mm/s
Første lag 30% 42.86 mm/s


0.6mm dyse (Volumetrisk hastighed: 27.0 mm³/s)

 Linjetype Procentdel Hastighed
Ekstern perimeter 50% 72.58 mm/s
Intern perimeter 75% 108.87 mm/s
Infill 100% 145.16 mm/s
Top/Bund 60% 87.10 mm/s
Første lag 30% 43.55 mm/s


0.8mm dyse (Volumetrisk hastighed: 48.0 mm³/s)

 Linjetype Procentdel Hastighed
Ekstern perimeter 50% 73.17 mm/s
Intern perimeter 75% 109.76 mm/s
Infill 100% 146.34 mm/s
Top/Bund 60% 87.80 mm/s
Første lag 30% 43.90 mm/s


1.0mm dyse (Volumetrisk hastighed: 75.0 mm³/s)

 Linjetype Procentdel Hastighed
Ekstern perimeter 50% 73.53 mm/s
Intern perimeter 75% 110.29 mm/s
Infill 100% 147.06 mm/s
Top/Bund 60% 88.24 mm/s
Første lag 30% 44.12 mm/s


5. Tilbagetrækningsindstillinger (Retraction)

Dyse Afstand Hastighed Z-Hop
0.4mm 0.5-0.8mm 45mm/s 0.2mm
0.6mm 0.6-1.0mm 45mm/s 0.2mm
0.8mm 0.8-1.2mm 40mm/s 0.2mm
1.0mm 1.0-1.5mm 35mm/s 0.2mm

6. Kølingsindstillinger

Kølingskonfiguration:

  • Første lag: 0% (blæser slukket)
  • Generel udskrivning: 100% blæserhastighed
  • Broer og udhæng: 100% blæserhastighed
  • Lag < 15 sekunder: 100% blæserhastighed

Kritiske overvejelser:

    • PLA kræver maksimal køling for de bedste resultater
    • Fuld blæserhastighed hjælper ved brobygning og udhæng
    • Det første lag kræver ingen køling for god vedhæftning
    • Små dele kræver maksimal køling

7. Fejlfindingsvejledning

 Problem Løsning
Dårlig lagvedhæftning

 

1. Øg temperaturen med 5-10°C

2. Reducer køleblæserens hastighed for de første par lag

3. Rengør byggeoverfladen med IPA

 
Warping (skævheder)

1. Øg pladetemperaturen til 60°C

2. Tilføj brim (5-10mm)

3. Sørg for, at der ikke er træk i udskrivningsområdet
Stringing (tråddannelse)

1. Sænk temperaturen med 5°C

2. Øg tilbagetrækningshastigheden til 45mm/s

3. Juster tilbagetrækningsafstanden
Under-ekstrudering

1. Øg temperaturen med 5-10°C

2. Rengør dysen eller prøv et cold pull

3. Kontrollér filamentets kvalitet
Dårlige udhæng

1. Sørg for 100% køling

2. Reducer temperaturen med 5°C

3. Reducer udskrivningshastigheden med 50%

 

BEMÆRK: Disse udskrivningsparametre er indledende anbefalinger baseret på vores erfaring. De skal muligvis justeres afhængigt af din specifikke 3D-printer, miljøforhold og geometrien på den del, du udskriver. Brug disse indstillinger som udgangspunkt og finjuster dem efter dine specifikke behov.

Coex 3D Filament Slicer Profiles

CX08 PLA Prime Technical Data Sheet

Technical Data Sheet: CX08 PLA PRIME SERIES 3D PRINTING FILAMENT

TDS Rev 2.0

BASE RESIN: NatureWorks Ingeo Biopolymer

Physical Properties

PropertyStandardUnitTypical Value
Specific Gravity - DensityASTM D792g/cc1.24
Melt Flow Rate @210°C/2.16 kgASTM D1238g/10 min7-9
Rel. Vis. @ 1.0 g/dL in CHCl₃ @30°CASTM D5225g/dL4.0

Mechanical Properties

PropertyStandardUnitTypical Value
Tensile Yield StrengthASTM D638MPa51
Tensile ModulusASTM D638MPa2315
Tensile ElongationASTM D638%3.31
Tensile StrengthASTM D638MPa50
Notched Izod ImpactASTM D256J/m118
Shrinkage Rate < 0.5%ASTM D955mm/mm.0002

Thermal Properties

PropertyStandardUnitTypical Value
Glass Transition Temperature (Tg)ASTM D3418°C55 - 60
Heat Distortion Temp @ 0.45MPaASTM E2092°C80 - 90
Decomposition TemperatureASTM D3418°C250

SPECIFICATIONS

Filament Size:1.75mm(in)2.85mm(in)
MIN Diameter:1.72mm0.0677 in2.79mm0.1098 in
MAX Diameter:1.78mm0.0701 in2.91mm0.1146 in
Tolerance+/- .03mm+/- 0.0012 in+/- .06mm+/- 0.0024 in

CERTIFICATIONS

Filament Complies with 2008 Consumer Product Safety Improvement Act (CPSIA) 2008

Filament Complies with CONEG Regulations

Filament Complies with RoHS Directive 2002/95/EC

FCN 000178 for the resin became effective on 1/3/2002 and is a permitted component of food packaging materials pursuant to set. 201(s) of the Federal Food, Drug, and Cosmetic Act, and parts 182, 184, and 186 of the Food Additive Regulations.

Printed Specimen Conditions

Printer:Open Source FDM/FFF
Nozzle:0.4mm
Layer Height:0.25mm
Infill:100%, +/-45°
Extrusion Temp:225°C
Bed Temp:None Needed (or 50 – 70°C if applicable)
Specimen Orientation:XY Flat
Annealed at 110°C/15 min.

Disclaimer: The technical data contained on this data sheet is furnished without charge or obligation and accepted at the recipient's sole risk. This data should not be used to establish specifications limits or used alone as the basis of design. The data provided is not intended to substitute any testing that may be required to determine fitness for any specific use.

``` PropertyStandardUnitTypical Value Glass Transition Temperature (Tg)ISO 11357-2°C-50.0Melt Temperature-°C152Drying Temperature @ 3 hours-°C80

SPECIFICATIONS

Filament Size:1.75mm(in)2.85mm(in)
MIN Diameter:1.72mm0.0677 in2.79mm0.1098 in
MAX Diameter:1.78mm0.0701 in2.91mm0.1146 in
Tolerance+/- .03mm+/- 0.0012 in+/- .06mm+/- 0.0024 in

ADVANTAGES

  • Resilient, Flexible, Heat Resistant, Chemical Resistant, Strong, Durable
  • Contains up to 60% renewably sourced materials from biomass
  • Combines the flexibility of rubber with the strength and processability of thermoplastics

Printed Specimen Conditions

Printer:Open Source FDM/FFF
Nozzle:0.4mm
Layer Height:0.25mm
Infill:100%, +/-45°
Extrusion Temp:210 - 250°C
Bed Temp:85°C
Specimen Orientation:XY Flat and Vertical
Printing Speed20mm/sec..

Disclaimer: The technical data contained on this data sheet is furnished without charge or obligation and accepted at the recipient's sole risk. This data should not be used to establish specifications limits or used alone as the basis of design. The data provided is not intended to substitute any testing that may be required to determine fitness for any specific use.

Download TDS (PDF)

CX08 PLA Prime Safety Data Sheet

Material Safety Data Sheet: CX08 PLA PRIME SERIES 3D PRINTING FILAMENT

MSDS Rev 1.0

BASE RESIN: NatureWorks™ Ingeo 3D850

1. Identification of the substance/preparation and of the company

1.1 Trade name:Coex PLA Prime 3D printer filament
1.2 Use of the product:3D printer filament, thermoplastic.
1.3 Supplier:Coex
660 Corporate WAY
Pulaski, WI 54162
Phone: (920) 757-1055

2. Hazards identification

2.1 Classification:Not classified
2.2 Special advice on hazards:None

3. Composition / information on ingredients

3.1 Chemical characteristics:

CAS #Hazardous ComponentsConcentration
9051-89-2Polylactide resin>=98%

4. First-aid measures

4.1 On skin contact:In case of contact with molten polymer immediately cool the skin with cold water. Medical aid may be required to remove adhering material and for treatment of burns.
4.2 After inhalation:Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid.
4.3 On ingestion:If swallowed, wash out mouth with water provided person is conscious. Do NOT induce vomiting.
4.4 On eyes contact:In case of contact, immediately flush eyes with copious amounts of water for at least (15) minutes.

5. Fire-fighting measures

5.1 Suitable fire extinguishing media:Water spray, chemical powder or carbon dioxide.
5.2 Special exposure hazards:During a fire, smoke may contain the original material in addition to combustion products of varying composition which may be toxic and/or irritating. Combustion products may include and are not limited to: Carbon dioxide. Carbon monoxide.
5.3 Special protective equipment:Self-contained breathing apparatus
5.4 Remark:Cool containers / tanks with water spray. Water mist may be used to cool closed containers. Fine dust dispersed in air may ignite. Risks of ignition followed by flame propagation or secondary explosions shall be prevented by avoiding accumulation of dust, e.g. on floors and ledges.

6. Accidental release measures

6.1 Personal precautions:Spilled material may cause a slipping Hazard.
6.2 Methods for cleaning up:Vacuum or sweep up material and place into a suitable disposal container.

7. Handling and storage

7.1 Handling:Avoid contact with molten polymer. Avoid generation of dust and electrostatic charge.
7.2 Storage:Protect against moisture. Store cool and keep packaging closed when not in use. Avoid sources of ignition.

8. Exposure controls/ personal protection

8.1 Technical safety measures:Use with adequate ventilation. Minimize dust generation and accumulation as combustible dust mixtures may be formed.
8.2 Personal safety equipment:Use adequate safety equipment, e.g. protective clothing, eye protection glasses, heat protection gloves. In case of dust formation wear mask with particle filter.
8.3 Work hygiene:No eating or drinking during working. Avoid contact of hot material with the skin. Avoid breathing dust and vapors.

9. Physical and chemical properties

9.1 Form:Spool
9.2 Color:Various
9.3 Odor:Sweet
9.4 Melting Temperature:150-180C
9.5 Oxidizing properties:Not self-igniting / flammable
9.6 Explosions limits:No test data
9.7 Density:1.25 g/cm³
9.8 Solubility in water:Insoluble

10. Stability and reactivity

10.1 Stability:The product is stable at recommended storage conditions.
10.2 Conditions to be avoided:Stable under recommended conditions of storage and handling.
10.3 Substances to be avoided:No special recommendations.
10.4 Hazardous decomposition products:Decomposition products depend upon temperature, air supply and the presence of other materials. Processing may release fumes and other decomposition products. At temperatures exceeding melt temperatures, polymer fragments can be released. Fumes can be irritating. Decomposition products can include and are not limited to: Combustible gases.

11. Toxicological information

11.1 Local irritation:Eye, Skin, Inhalation, Ingestion.
11.2 Other remarks:Product dust may be irritating to eyes, skin and respiratory system. Resin particles, like other inert materials are mechanically irritating to eyes. Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhea.

12. Ecological information

12.1 Ecological info:EC50/72h/algae > 1100 mg/L
12.2 Biological degradation:Inherently biodegradable under industrial composting conditions.
12.3 Bioaccumulation:Not expected to bioconcentrate or bioaccumulate. Data for Component: White mineral oil (petroleum)(8042-47-5) Bioconcentration potential is high (BCF > 3000 or Log Pow between 5 and 7). Bioconcentration Factor (BCF): 1,900; Fish; Estimated.

13. Disposal considerations

13.1 Product:In accordance with local and national regulations. Should not be released into the environment. Do not contaminate ponds, waterways or ditches with chemical or used container.
13.2 Uncleaned packaging:Packaging material has to be emptied completely and disposed in accordance with the regulations. Packaging can be recycled if not contaminated.

14. Transport information

14.1 Transport regulations:Not classified as hazardous under transport regulations DOT, ICAO/IATA, IMDG/GGVSee, ICAO/IATA

15. Regulatory information

15.1 EPA regulations:Sara 313 title III: Not Listed
TSCA Inventory List: Listed

16. Other information

This data is based on the current state of our information and experience. This safety data sheet describes our product in terms of safety requirements. Preceding data is not applicable as a warranty of product properties. It is the responsibility of the recipient to observe the existing legal regulations for the use of this product.

Disclaimer: The safety data contained on this data sheet is furnished without charge or obligation and accepted at the recipient's sole risk. This data describes our product in terms of safety requirements. The data provided is not applicable as a warranty of product properties. It is the responsibility of the recipient to observe the existing legal regulations for the use of this product.

Download SDS (PDF)

Stone Grey PLA Prime

Spar $4.00
SKU: CX08-7200-18-1KG
2 anmeldelser
Diameter: 1,75 mm
Vægt: 1 kg
Pris:
$28.00 $32.00
Lager:
Lager: 19
Select Color: Stone Grey PLA Prime

Du vil måske også kunne lide

Senest viste