Før musen over billedet for at zoome ind Klik på billedet for at zoome

Chokoladebrun PLA

HEX #402000TD 0.6

Coex 3D Chokoladebrun PLA

Lås op for præcisionsprint med Coex 3D Standard PLA-filament - det pålidelige fundament for din kreative vision. Vores premium PLA-filament (polylaktid) leverer enestående kvalitet til skabere på alle niveauer.

Hovedegenskaber:

Konsekvent 1,75 mm diameter med en snæver tolerance på ±0,03 mm for jævn, problemfri printning uden stop
Fremstillet af vedvarende plantebaserede ressourcer til miljøbevidst skabelse
Kompatibel med alle standard FDM/FFF 3D-printere
Lav tendens til vridning og minimal lugt under printning
Levende, falmebestandige farver, der bevarer deres integritet gennem hele printprocessen

Uanset om du laver prototyper af et nyt design, skaber funktionelle dele eller bringer kunstneriske koncepter til live, leverer Coex 3D Standard PLA pålidelig ydeevne print efter print. Hver spole er vakuumpakket med tørremiddel for at sikre optimal beskyttelse mod fugt og kommer med 100% tilfredshedsgaranti.

Løft din 3D-printoplevelse i dag med Coex 3D Standard PLA - hvor kvalitet møder kreativitet.

Coex's PLA er lavet med ren NatureWorks Ingeo 4043D-resin, kun farvestoffer af høj kvalitet og ingen fyldstoffer.

Alt Coex 3D-filament er fremstillet på vores produktionsanlæg i Wisconsin, USA.

Vores Standard PLA er lige så god som eller bedre end de fleste konkurrenters PLA+ eller PLA Prime.

Teknisk udskriftsvejledning - COEX PLA

1. Bemærkninger om materialet

Hold filamentet tørt - opbevar det korrekt og tør det før brug
PLA er mindre hygroskopisk end andre materialer, men korrekt opbevaring hjælper med at bevare kvaliteten
Om nødvendigt tørres det ved 55°C i 3 timer eller mere
Tjek for eventuelle synlige skader før brug

2. Temperaturindstillinger

Pladetemperatur: 60°C

Vask printpladen ofte for at sikre god vedhæftning - Brug opvaskemiddel og skyl grundigt for at fjerne olier
Brug produkter til pladevedhæftning hvis nødvendigt (limstift, WELD3D)
Brug "brim" (kant) til høje eller store emner
Hold den omgivende temperatur stabil

Ekstrudertemperatur: 215-235°C

3. Grundlæggende parametre

PLA (Polylactic Acid) er en biologisk nedbrydelig polymer kendt for sin brugervenlighed under print, gode overfladekvalitet og dimensionelle nøjagtighed. Perfekt til dekorative dele, prototyper og generelle behov, hvor mekaniske egenskaber ikke er kritiske.

Dyse	Lagtykkelse	Linjebredde	Volumetrisk hastighed	Temperatur
0.4mm	0.2mm	0.42mm	12.0 mm³/s	220°C
0.6mm	0.3mm	0.62mm	27.0 mm³/s	225°C
0.8mm	0.4mm	0.82mm	48.0 mm³/s	230°C
1.0mm	0.5mm	1.02mm	75.0 mm³/s	235°C

4. Hastighedsindstillinger

0.4mm dyse (Volumetrisk hastighed: 12.0 mm³/s)

Linjetype	Procentdel	Hastighed
Udvendig væg	50%	71.43 mm/s
Indvendige vægge	75%	107.14 mm/s
Udfyldning (infill)	100%	142.86 mm/s
Top/Bund	60%	85.71 mm/s
Første lag	30%	42.86 mm/s

0.6mm dyse (Volumetrisk hastighed: 27.0 mm³/s)

Linjetype	Procentdel	Hastighed
Udvendig væg	50%	72.58 mm/s
Indvendige vægge	75%	108.87 mm/s
Udfyldning (infill)	100%	145.16 mm/s
Top/Bund	60%	87.10 mm/s
Første lag	30%	43.55 mm/s

0.8mm dyse (Volumetrisk hastighed: 48.0 mm³/s)

Linjetype	Procentdel	Hastighed
Udvendig væg	50%	73.17 mm/s
Indvendige vægge	75%	109.76 mm/s
Udfyldning (infill)	100%	146.34 mm/s
Top/Bund	60%	87.80 mm/s
Første lag	30%	43.90 mm/s

1.0mm dyse (Volumetrisk hastighed: 75.0 mm³/s)

Linjetype	Procentdel	Hastighed
Udvendig væg	50%	73.53 mm/s
Indvendige vægge	75%	110.29 mm/s
Udfyldning (infill)	100%	147.06 mm/s
Top/Bund	60%	88.24 mm/s
Første lag	30%	44.12 mm/s

5. Tilbagetrækningsindstillinger (Retraction)

Dyse	Afstand	Hastighed	Z-Hop
0.4mm	0.5-0.8mm	45mm/s	0.2mm
0.6mm	0.6-1.0mm	45mm/s	0.2mm
0.8mm	0.8-1.2mm	40mm/s	0.2mm
1.0mm	1.0-1.5mm	35mm/s	0.2mm

6. Kølingsindstillinger

Kølingskonfiguration:

Første lag: 0% (blæser slukket)
Generel udskrivning: 100% basisblæserhastighed
Broer og udhæng: 100% blæserhastighed
Lag < 15 sekunder: 100% blæserhastighed

Kritiske overvejelser:

PLA kræver maksimal køling for at opnå de bedste resultater
Fuld blæserhastighed hjælper ved broer og udhæng
Det første lag behøver ingen køling for at sikre god vedhæftning
Små dele kræver maksimal køling

7. Fejlfindingsvejledning

Problem	Løsning
Dårlig lagvedhæftning	1. Øg temperaturen med 5-10°C 2. Reducer blæserhastigheden for de første par lag 3. Rengør printoverfladen med IPA (isopropylalkohol)
Vridning (Warping)	1. Øg pladetemperaturen til 60°C 2. Tilføj en "brim" (kant) (5-10mm) 3. Sørg for, at der ikke er træk i printområdet
Stringing (tråddannelse)	1. Sænk temperaturen med 5°C 2. Øg tilbagetrækningshastigheden til 45mm/s 3. Juster tilbagetrækningsafstanden
Under-ekstrudering	1. Øg temperaturen med 5-10°C 2. Rengør dysen eller forsøg med et "cold pull" 3. Tjek filamentets kvalitet
Dårlige udhæng	1. Sørg for 100% køling 2. Reducer temperaturen med 5°C 3. Reducer printhastigheden med 50%

BEMÆRK VENLIGST: Disse udskriftsparametre er indledende anbefalinger baseret på vores erfaring. De skal muligvis justeres afhængigt af din specifikke 3D-printer, miljøforhold og geometrien på den del, du printer. Brug disse indstillinger som et udgangspunkt og finjuster dem efter dine specifikke behov.

Coex 3D Filament Slicer Profiles

CX02 PLA Technical Data Sheet

Technical Data Sheet: CX02 PLA SERIES 3D PRINTING FILAMENT

TDS Rev 2.0

BASE RESIN: NatureWorks Ingeo Biopolymer

Physical Properties

Property	Standard	Unit	Typical Value
Specific Gravity - Density	ASTM D792	g/cc	1.24
Melt Flow Rate @210°C/2.16 kg	ASTM D1238	g/10 min	6
Rel. Vis. @ 1.0 g/dL in CHCl₃ @30°C	ASTM D5225	g/dL	4.0

Mechanical Properties

Property	Standard	Unit	Typical Value
Tensile Yield Strength	ASTM D638	MPa	60
Tensile Modulus	ASTM D638	MPa	3.6
Tensile Elongation	ASTM D638	%	6
Tensile Strength	ASTM D638	MPa	53
Notched Izod Impact	ASTM D256	J/m	16
Shrinkage Rate < 0.5%	ASTM D955	mm/mm	.0002

Thermal Properties

Property	Standard	Unit	Typical Value
Glass Transition Temperature (Tg)	ASTM D3418	°C	55 - 60
Heat Distortion Temp @ 0.45MPa	ASTM E2092	°C	55
Decomposition Temperature	ASTM D3418	°C	250

SPECIFICATIONS

Filament Size:	1.75mm	(in)	2.85mm	(in)
MIN Diameter:	1.72mm	0.0677 in	2.79mm	0.1098 in
MAX Diameter:	1.78mm	0.0701 in	2.91mm	0.1146 in
Tolerance	+/- .03mm	+/- 0.0012 in	+/- .06mm	+/- 0.0024 in

CERTIFICATIONS

Filament Complies with 2008 Consumer Product Safety Improvement Act (CPSIA) 2008

Filament Complies with CONEG Regulations

Filament Complies with RoHS Directive 2002/95/EC

FCN 000178 for the resin became effective on 1/3/2002 and is a permitted component of food packaging materials pursuant to set. 201(s) of the Federal Food, Drug, and Cosmetic Act, and parts 182, 184, and 186 of the Food Additive Regulations.

Printed Specimen Conditions

Printer:	Open Source FDM/FFF
Nozzle:	0.4mm
Layer Height:	0.25mm
Infill:	100%, +/-45°
Extrusion Temp:	225°C
Bed Temp:	None Needed (or 50 – 70°C if applicable)
Specimen Orientation:	XY Flat
Annealed at 110°C/15 min.

Disclaimer: The technical data contained on this data sheet is furnished without charge or obligation and accepted at the recipient's sole risk. This data should not be used to establish specifications limits or used alone as the basis of design. The data provided is not intended to substitute any testing that may be required to determine fitness for any specific use.

Download TDS (PDF)

CX02 PLA Safety Data Sheet

Safety Data Sheet: CX02 PLA SERIES 3D PRINTING FILAMENT

SDS Rev 1.0

BASE RESIN: NatureWorks™ Ingeo 4043D

1. Identification of the substance/preparation and of the company

1.1 Trade name:Coex PLA 3D printer filament

1.2 Use of the product:3D printer filament, thermoplastic.

1.3 Supplier:Coex
660 Corporate WAY
Pulaski, WI 54162
Phone: (920) 757-1055

2. Hazards identification

2.1 Classification:This product is NOT classified according to 29 CFR 1910.1200 Hazard Communication Standard 2012

2.2 Special advice on hazards:If small particles are generated during further processing, handling, or by other means, combustible dust concentrations in air may form.

3. Composition / information on ingredients

3.1 Chemical characteristics:

CAS #	Hazardous Components	Concentration
9051-89-2	Polylactide resin	>=98%

4. First-aid measures

4.1 On skin contact:In case of contact with molten polymer immediately cool the skin with cold water. Medical aid may be required to remove adhering material and for treatment of burns.

4.2 After inhalation:Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid.

4.3 On ingestion:If swallowed, wash out mouth with water provided person is conscious. Do NOT induce vomiting.

4.4 On eyes contact:In case of contact, immediately flush eyes with copious amounts of water for at least (15) minutes.

5. Fire-fighting measures

5.1 Suitable fire extinguishing media:Water spray, chemical powder or carbon dioxide.

5.2 Special exposure hazards:During a fire, smoke may contain the original material in addition to combustion products of varying composition which may be toxic and/or irritating. Combustion products may include and are not limited to: Carbon dioxide. Carbon monoxide.

5.3 Special protective equipment:Self-contained breathing apparatus

5.4 Remark:Cool containers / tanks with water spray. Water mist may be used to cool closed containers. Fine dust dispersed in air may ignite. Risks of ignition followed by flame propagation or secondary explosions shall be prevented by avoiding accumulation of dust, e.g. on floors and ledges.

6. Accidental release measures

6.1 Personal precautions:Spilled material may cause a slipping Hazard.

6.2 Methods for cleaning up:Vacuum or sweep up material and place into a suitable disposal container.

7. Handling and storage

7.1 Handling:Avoid contact with molten polymer. Avoid generation of dust and electrostatic charge.

7.2 Storage:Protect against moisture. Store cool and keep packaging closed when not in use. Avoid sources of ignition.

8. Exposure controls/ personal protection

8.1 Technical safety measures:Use with adequate ventilation. Minimize dust generation and accumulation as combustible dust mixtures may be formed.

8.2 Personal safety equipment:Use adequate safety equipment, e.g. protective clothing, eye protection glasses, heat protection gloves. In case of dust formation wear mask with particle filter.

8.3 Work hygiene:No eating or drinking during working. Avoid contact of hot material with the skin. Avoid breathing dust and vapors.

9. Physical and chemical properties

9.1 Form:Spool

9.2 Color:Various

9.3 Odor:Sweet

9.4 Melting Temperature:150-180C

9.5 Oxidizing properties:Not self-igniting / flammable

9.6 Explosions limits:No test data

9.7 Density:1.25 g/cm³

9.8 Solubility in water:Insoluble

10. Stability and reactivity

10.1 Stability:The product is stable at recommended storage conditions.

10.2 Conditions to be avoided:Stable under recommended conditions of storage and handling.

10.3 Substances to be avoided:No special recommendations.

10.4 Hazardous decomposition products:Decomposition products depend upon temperature, air supply and the presence of other materials. Processing may release fumes and other decomposition products. At temperatures exceeding melt temperatures, polymer fragments can be released. Fumes can be irritating. Decomposition products can include and are not limited to: Combustible gases.

11. Toxicological information

11.1 Local irritation:Eye, Skin, Inhalation, Ingestion.

11.2 Other remarks:Product dust may be irritating to eyes, skin and respiratory system. Resin particles, like other inert materials, are mechanically irritating to eyes. Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhea.

12. Ecological information

12.1 Ecological info:EC50/72h/algae > 1100 mg/L

12.2 Biological degradation:Inherently biodegradable under industrial composting conditions.

12.3 Bioaccumulation:Not expected to bioconcentrate or bioaccumulate. Data for Component: White mineral oil (petroleum)(8042-47-5) Bioconcentration potential is high (BCF > 3000 or Log Pow between 5 and 7). Bioconcentration Factor (BCF): 1,900; Fish; Estimated.

13. Disposal considerations

13.1 Product:In accordance with local and national regulations. Should not be released into the environment. Do not contaminate ponds, waterways or ditches with chemical or used container.

13.2 Uncleaned packaging:Packaging material has to be emptied completely and disposed in accordance with the regulations. Packaging can be recycled if not contaminated.

14. Transport information

14.1 Transport regulations:Not classified as hazardous under transport regulations DOT, ICAO/IATA, IMDG/GGVSee, ICAO/IATA

15. Regulatory information

15.1 EPA regulations:Sara 313 title III: Not Listed
TSCA Inventory List: Listed

16. Other information

This data is based on the current state of our information and experience. This safety data sheet describes our product in terms of safety requirements. Preceding data is not applicable as a warranty of product properties. It is the responsibility of the recipient to observe the existing legal regulations for the use of this product.

Disclaimer: The safety data contained on this data sheet is furnished without charge or obligation and accepted at the recipient's sole risk. This data describes our product in terms of safety requirements. The data provided is not applicable as a warranty of product properties. It is the responsibility of the recipient to observe the existing legal regulations for the use of this product.

Download SDS (PDF)

Chokoladebrun PLA

Spar $3.00

SKU: CX02-0700-18-1KG

3 anmeldelser

Diameter: 1,75 mm

Vægt: 1 kg

Variant

Pris:

$21.00 $24.00

Lager:

Lager: 47

Antal:

Del dette produkt

Select Color: Chokoladebrun PLA