{"title":"Reinforced Materials","description":"","products":[{"product_id":"flame-retardant-black-abs","title":"Flame Retardant Black ABS","description":"\u003cp\u003eFlame Retardant ABS is made from a UL94 V-0 rated ABS base resin, for parts that need to self-extinguish, such as electrical enclosures and housings near heat sources.\u003c\/p\u003e\u003ch3\u003eUL94 flame rating of the base resin\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003cth\u003eRating\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e1.5mm\u003c\/td\u003e\n\u003ctd\u003eV-0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2.0mm\u003c\/td\u003e\n\u003ctd\u003eV-0, 5VB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2.5mm\u003c\/td\u003e\n\u003ctd\u003eV-0, 5VA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3.0mm\u003c\/td\u003e\n\u003ctd\u003eV-0, 5VA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003eThese are the UL94 ratings of the base resin used to make COEX 3D Flame Retardant ABS filament. They are not ratings of a finished printed part. How a printed part performs depends on its geometry, wall thickness and print settings, so test parts for your application. The UL yellow card is available on request.\u003c\/p\u003e\u003ch3\u003eVentilation is required\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eUse direct ventilation. Vent outdoors, or through HEPA and carbon filtration.\u003c\/li\u003e\n\u003cli\u003eNever let Flame Retardant ABS cool in the nozzle. Remove it while the nozzle is still hot, then purge with standard ABS.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTolerance: ±0.03 mm (1.75 mm) · ±0.06 mm (2.85 mm)\u003c\/li\u003e\n\u003cli\u003eOther spool sizes available by request: \u003ca href=\"\/pages\/contact\"\u003econtact us\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003eBacked by our defect guarantee: we replace or refund defective filament.\u003c\/li\u003e\n\u003cli\u003eExtruded, quality controlled and shipped from one plant in Green Bay, WI.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0603\/1795\/8327\/files\/COEX_TDS_CX16-FR_ABS_10-27-2026_REV_3.0.pdf?v=1793132916\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet\u003c\/a\u003e · \u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0603\/1795\/8327\/files\/COEX_YELLOW_CARD_CX16-ABS_FLAME_RETARDANT_02-01-24_REV_1.0.pdf?v=1729874254\" target=\"_blank\" rel=\"noopener\"\u003eUL yellow card\u003c\/a\u003e · \u003ca href=\"\/pages\/filament-parameters\"\u003ePrint settings\u003c\/a\u003e · \u003ca href=\"\/pages\/filament-slicer-profiles\"\u003eSlicer profiles\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003eBuying for a government or defense program? See our \u003ca href=\"\/pages\/government-vendor\"\u003eGovernment Vendor page\u003c\/a\u003e.\u003c\/p\u003e","brand":"COEX 3D","offers":[{"title":"1.75mm \/ 1kg","offer_id":41279438028983,"sku":"CX16-0300-18-1KG","price":52.0,"currency_code":"USD","in_stock":true},{"title":"1.75mm \/ 500g","offer_id":41279437963447,"sku":"CX16-0300-18-500G","price":33.0,"currency_code":"USD","in_stock":true},{"title":"1.75mm \/ 5lb","offer_id":41279437996215,"sku":"CX16-0300-18-5LB","price":115.0,"currency_code":"USD","in_stock":true},{"title":"2.85mm \/ 1kg","offer_id":41279438061751,"sku":"CX16-0300-30-1KG","price":52.0,"currency_code":"USD","in_stock":true},{"title":"2.85mm \/ 5lb","offer_id":51832442323308,"sku":"CX16-0300-30-5LB","price":115.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0603\/1795\/8327\/files\/Flame_Retardent.png?v=1762438671"},{"product_id":"black-coexnylex™-pa6-carbon","title":"Black COEXNylex™ PA6-CF","description":"\u003cp\u003eCOEXNylex PA6-CF is PA6 nylon reinforced with 10% carbon fiber, and it's our top-selling nylon. Use it for parts that have to carry load, hold their dimensions and take heat: jigs, fixtures and manufacturing aids, robotics frames and mechanical components, automotive and aerospace prototypes, and load-bearing end-use parts. Want nylon without the fiber? See the \u003ca href=\"\/collections\/coexnylex-natural\"\u003efull COEXNylex range\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eKey properties\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHigh strength-to-weight ratio and tensile strength\u003c\/li\u003e\n\u003cli\u003eDimensional stability and heat resistance for demanding engineering parts\u003c\/li\u003e\n\u003cli\u003eConsistent extrusion and strong layer adhesion despite the fiber content\u003c\/li\u003e\n\u003cli\u003eMatte black finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003ePrinting notes\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eUse a hardened steel or other wear-resistant nozzle. Carbon fiber wears brass.\u003c\/li\u003e\n\u003cli\u003eShips pre-dried, ready to print when you open it.\u003c\/li\u003e\n\u003cli\u003eNylon absorbs moisture. Reseal the spool with desiccant between prints, and dry an opened spool at 80°C for 8–12 hours before critical prints.\u003c\/li\u003e\n\u003cli\u003eNeed help dialing it in? Our engineering team can advise on settings.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eMaterial: COEXNylex PA6 nylon with 10% carbon fiber\u003c\/li\u003e\n\u003cli\u003eTolerance: ±0.03 mm (1.75 mm) · ±0.06 mm (2.85 mm)\u003c\/li\u003e\n\u003cli\u003eOther spool sizes available by request: \u003ca href=\"\/pages\/contact\"\u003econtact us\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003eVacuum-sealed with desiccant\u003c\/li\u003e\n\u003cli\u003eBacked by our defect guarantee: we replace or refund defective filament.\u003c\/li\u003e\n\u003cli\u003eExtruded, quality controlled and shipped from one plant in Green Bay, WI.\u003c\/li\u003e\n\u003cli\u003eSlicer profile: the COEX NYLEX PA6-CF profile for 1.75mm filament is built into OrcaSlicer 2.3.2 and later. In Filament Selection, choose vendor COEX 3D, then COEX NYLEX PA6-CF.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003ca href=\"\/pages\/filament-parameters\"\u003ePrint settings\u003c\/a\u003e · \u003ca href=\"\/pages\/filament-slicer-profiles\"\u003eSlicer profiles\u003c\/a\u003e · \u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0603\/1795\/8327\/files\/COEX_TDS_CX23-COEXNYLEX_PA6CF_10-26-2026_REV_2.0.pdf?v=1793039473\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet\u003c\/a\u003e · \u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0603\/1795\/8327\/files\/COEX_SDS_CX23-COEXNYLEX_PA6CF_10-26-2026_REV_3.0.pdf?v=1793039473\" target=\"_blank\" rel=\"noopener\"\u003eSafety data sheet\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003eBuying for a government or defense program? See our \u003ca href=\"\/pages\/government-vendor\"\u003eGovernment Vendor page\u003c\/a\u003e.\u003c\/p\u003e","brand":"COEX 3D","offers":[{"title":"1.75mm \/ 1kg","offer_id":52018123407724,"sku":"CX23-0300-18-1KG","price":85.0,"currency_code":"USD","in_stock":true},{"title":"1.75mm \/ 500g","offer_id":52386765701484,"sku":"CX23-0300-18-500G","price":60.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0603\/1795\/8327\/files\/PA6CF_S.webp?v=1762439435"},{"product_id":"carbon-pla","title":"Carbon Filled PLA","description":"\u003cp\u003eCarbon Filled PLA blends finely milled carbon fiber into a PLA base. Use it for parts that must stay stiff and hold their dimensions: jigs, fixtures, brackets and functional prototypes. The fiber also gives a matte surface that hides layer lines.\u003c\/p\u003e\u003ch3\u003eKey properties\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHigher stiffness and dimensional stability than standard PLA\u003c\/li\u003e\n\u003cli\u003eReduced warping and shrinkage\u003c\/li\u003e\n\u003cli\u003eMatte finish that hides layer lines\u003c\/li\u003e\n\u003cli\u003eStrong layer adhesion with minimal stringing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003ePrinting notes\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eUse a hardened steel or other wear-resistant nozzle. Carbon fiber wears brass.\u003c\/li\u003e\n\u003cli\u003ePrints on standard FDM\/FFF printers\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eMaterial: PLA with carbon fiber reinforcement\u003c\/li\u003e\n\u003cli\u003eTolerance: ±0.03 mm (1.75 mm) · ±0.06 mm (2.85 mm)\u003c\/li\u003e\n\u003cli\u003eOther spool sizes available by request: \u003ca href=\"\/pages\/contact\"\u003econtact us\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003eVacuum-sealed with desiccant\u003c\/li\u003e\n\u003cli\u003eBacked by our defect guarantee: we replace or refund defective filament.\u003c\/li\u003e\n\u003cli\u003eExtruded, quality controlled and shipped from one plant in Green Bay, WI.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003ca href=\"\/pages\/filament-parameters\"\u003ePrint settings\u003c\/a\u003e · \u003ca href=\"\/pages\/filament-slicer-profiles\"\u003eSlicer profiles\u003c\/a\u003e\u003c\/p\u003e","brand":"COEX 3D","offers":[{"title":"1.75mm \/ 1kg","offer_id":53601796489580,"sku":"CX02-0390-18-1KG","price":35.0,"currency_code":"USD","in_stock":true},{"title":"1.75mm \/ 500g","offer_id":67683561734508,"sku":"CX02-0390-18-500G","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0603\/1795\/8327\/files\/CARBONFILLEDPLASPOOL.png?v=1785954110"}],"url":"https:\/\/coex3d.com\/collections\/reinforced-materials.oembed","provider":"COEX 3D","version":"1.0","type":"link"}